Plumbing Basics: Your Key to Installing a Bathtub
Plumbing Basics: Your Key to Installing a Bathtub
Blog Article
This great article following next about How to Install a Bathtub Yourself is rather interesting. Give it a go and make your own results.
Mounting a bathtub isn't exactly brain surgery, yet it does need solid plumbing, carpentry, and occasionally, tiling abilities. Changing an old tub with a new one is additionally a reasonably tough job. If the old tub is easily easily accessible, the job can move rapidly; if you have to open up a wall surface to eliminate the old tub and place the brand-new tub, the job is a lot harder. In either case, the task is within a residence handyman's skills, although you will certainly need a helper to move out the old bathtub and embeded in the brand-new one. Make certain you have actually certified on your own for the task and are comfortable trying it. Rather than hiring a specialist to take over a halfway-completed job, it is better to consider using one prior to you begin. Possibilities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your bathroom if you have currently acquired a brand-new bathtub and also do not require to alter the arrangement of your previous supply of water pipes.
Your devices as well as material checklist should consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be rather bothersome due to the restricted access that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric all set for the staying water that will certainly come from the pipes. When the supply pipes have been gotten rid of, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning throughout this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in place in between the tap and the sink. Protect the faucet in place with the supplier offered backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind needs to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bathtub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in uniformly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level reads level.
To install taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression join; then do the exact same for the other faucet.
Turn on the water system as well as examine all joints as well as new pipework for leaks and tighten them if required. Fill up the bath tub as well as likewise check the overflow electrical outlet and the regular outlet for leaks.
Finally, deal with the bath paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the tub should wait till the bathtub has actually been utilized a minimum of when as this will resolve it into its last setting.
Getting ready for the Installation
To start with, the supporting framework provided with the bath must be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the tap features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its last position.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to break an inflexible seal, causing the water to penetrate the wall in between the bathroom and also the tiling, bring about complications with dampness and possible leakages to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to enable the activity experienced when the bathtub remains in usage. The sealer can break fairly early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise conveniently readily available on the market. It is a good idea to fit the ceramic tiles using waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading about Tools You Need to Install a New Bathtub ? Place a remark directly below. We'd be pleased to listen to your thinking about this content. Hoping that you come back again before long. Those who enjoyed reading our post kindly be sure to pass it around. Thanks a bunch for your time. Please stop by our site back soon.
Schedule Now Report this page